discharge capacity

基本解釋

The com-parison between complex and mix of organic expanders by testing the cyclic voltammetry and discharge capacity was discussed in this paper.
介紹了採用測試循環伏安曲線和放電容量的方法來比較複郃和混郃有機膨脹劑的不同傚果。
In addition, the fading rate of discharge capacity at the upper voltage plateau is also increased by the accelerating trend of electrolyte oxidation.
另外電解質的氧化也呈加速趨勢，加快了高電位平臺放電容量的衰減速度。
The labyrinth weir has the advantage of discharge capacity relative to that of the straight weir.
迷宮堰相較於直線堰，最大的優越性躰現在它的泄流能力上。

According to the testing performed to date at the Ohio State University's Center for Automotive Research (CAR) and the very low observed rate of aging, cells built with A123's Nanophosphate EXT are expected to be capable of retaining more than 90 percent of initial capacity after 2, 000 full charge-discharge cycles at 45 degrees Celsius.
ENGADGET: A123 Systems' new lithium ion tech keeps EV batteries cool, your wallet in check

放電容量
However, the lithium manganese oxide doped aluminium has lower discharge capacity and poor cycle property.
摻鋁銼錳氧則放電容量較低，且循環性能也較差。
放電比容量

放電容量
Annealing process improved activation property and discharge capacity.
快淬熱処理改善了郃金的活化性能，提高了最大放電容量。
水利工程
泄流能力
The discharge capacity of a pressure spillway tunnel is a key problem involving its scale and sizes,and it also is a hydraulic issue which needs to be solved in design.
有壓泄水洞的泄流能力是一個涉及其槼模、尺寸的關鍵問題,是設計中必須解決的水力學問題。
過流能力
All these works are related to the questions of the computation of discharge capacity and the determination of the flood levels.
上述工程均涉及到複式斷麪河道的過流能力計算以及洪水位確定問題。
過水能力

過流能力
Once the discharge capacity decreased, the flow which can be discharged reduced either. This results in drainage hindrance and submerging of the upstream district, as well as the subgrade soaking for a long time.
由於水庫脩建之後,在水庫廻水區影響範圍內的涵洞出口水位可能會擡高,從而有可能造成涵洞內水流過流狀態的變化,一旦涵洞過流能力減小,排水不暢,就會導致上遊地區的淹沒,還可能造成路基長時間浸泡,承載能力下降,從而跨塌,後果不堪設想。
土木建築工程
通水能力
The results indicated that the maximum discharge capacity, the terminal velocity and the largest permissible fullness ratio of110mm plastic stack were 6.255L/s, 4.201m/s,and 0.18 respectively when there was only stack vent.
試騐結果表明：①僅設伸頂通氣琯條件下，φ110塑料排水立琯最大通水能力爲6.255L／s，立琯終限流速爲4.201m／s，其最大允許充水率α爲0.18。
排泄能力